Fort Lauderdale Gate Pros provides professional sliding gates in Fort Lauderdale, FL for residential and commercial properties across Broward County. A ground track through a Fort Lauderdale driveway is a channel that collects water, sand and salt, then holds all three against steel wheels. It works beautifully for two years and becomes a service call every month after that.
The problem is not the track, it is that nothing drains here. Sites near the water sit on sand with the water table close under the surface, so a track set flush in concrete fills after every storm and stays wet. Wheel bearings are sealed against splash, not immersion. Once the seal loses, the bearing packs with grit and the operator starts pulling amps to move a gate that used to glide.
Where a V track is right, we detail it properly: a drain to daylight at the low end, stainless or coated wheels, and a track profile that sheds rather than cups. Where it is wrong, we say so and price a cantilever instead, which keeps the whole rolling assembly off the ground and out of the standing water. Replace sealed bearings on a schedule, because a wheel is a twenty minute part and a gearbox is not.
Cantilever is not automatically the answer either. It needs a tail run roughly half the opening again behind the gate, and a lot of isle properties simply do not have that side yard. When there is no tail room and the opening is modest, a swing pair or a bi-parting slide is cheaper and more durable than forcing a cantilever into a space that fights it. We would rather say that at the survey than after the pour.
Whichever type you end up with, the buried run matters as much as the gate. Conduit under a driveway on the water fills with groundwater, so we use direct burial rated conductors that do not care, and we bring every conduit into the operator from below with a drip loop rather than through the top of the housing. Code treats an underground raceway as a wet location for exactly that reason.
Two details at the far end decide how a slide gate ages. The receiving post takes the leaf's free end and should capture it rather than merely stop it, so the gate cannot be levered off its line. The guide rollers that hold the leaf upright sit lowest of anything on the assembly, which on a driveway that floods means they are the first bearings to pack with grit and the first to replace.
If your existing slide gate has started shuddering, do not start with the operator. Nine times out of ten here the wheels are gone and the motor has been compensating for months.
With 15+ years of experience, our insured team brings the right materials and equipment to every job — wrought iron and ornamental steel fabrication, marine-grade powder-coated aluminum, cantilever and roller slide gates, LiftMaster, DoorKing and FAAC operators, Class I-IV operator classifications, UL 325 entrapment protection — and backs the work with a written workmanship warranty. We serve Fort Lauderdale and nearby communities including Pompano Beach, Oakland Park, Wilton Manors, Lauderdale-by-the-Sea.
What We Handle
Everything our sliding gates in Fort Lauderdale covers
One crew, one point of contact, and the full range of sliding gates work in Fort Lauderdale, FL. If it is on this list we do it in house rather than handing it to a subcontractor:
- sliding driveway gates
- rolling gates Fort Lauderdale
- track slide gates
- V-track and roller gates
- sliding gate operators
- sliding gate repair
- slide gate roller replacement
- commercial rolling gates
- slide gate track cleaning
- waterfront slide gates
- sliding gate safety sensors
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Fort Lauderdale services.
Materials, equipment and how we do sliding gates
The difference between sliding gates that lasts and sliding gates that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with wrought iron and ornamental steel fabrication, marine-grade powder-coated aluminum, cantilever and roller slide gates, LiftMaster, DoorKing and FAAC operators, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Fort Lauderdale job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. 15+ years of gate work in Broward County means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do sliding gates outside Fort Lauderdale
Fort Lauderdale Gate Pros covers Fort Lauderdale and the surrounding communities of Broward County. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Sliding Gates in Pompano Beach, FL — Broward County, incorporated as the Town of Pompano on July 3, 1908, population 112,046 at the 2020 census
- Sliding Gates in Oakland Park, FL — Broward County, incorporated as Floranada on November 25, 1925, population 44,229 at the 2020 census
- Sliding Gates in Wilton Manors, FL — Broward County, incorporated as a village on May 13, 1947, population 11,426 at the 2020 census
- Sliding Gates in Lauderdale-by-the-Sea, FL — Broward County, incorporated November 30, 1927, population 6,198 at the 2020 census
- Sliding Gates in Lighthouse Point, FL — Broward County, incorporated as a town on June 13, 1956, population 10,486 at the 2020 census
- Sliding Gates in Deerfield Beach, FL — Broward County, incorporated as a town on May 12, 1939, population 86,859 at the 2020 census
Start on the Fort Lauderdale Gate Pros homepage for a free estimate, or call (844) 938-4596 and describe the job.
Why Fort Lauderdale Chooses Fort Lauderdale Gate Pros
- ✓Over 15 years installing and automating gates across Broward County
- ✓In-house metal shop — we weld and powder coat our own gates rather than drop-shipping them
- ✓Marine-grade aluminum and hot-dip galvanized steel specified for coastal salt air
- ✓Waterfront, canal-front and marina-community gate work is a specialty, not a sideline
The standards behind sliding gates
Quality here is not a matter of opinion — it is written down. The sliding gates work we do in Fort Lauderdale follows published industry standards: DASMA is the standards body for door and access systems, and UL Solutions publishes UL 325, the safety standard for automatic gate operators. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every sliding gates project in Fort Lauderdale gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 938-4596 for a free sliding gates free estimate in Fort Lauderdale, or request a quote and we'll get right back to you.