Fort Lauderdale Gate Pros provides professional aluminum gates in Fort Lauderdale, FL for residential and commercial properties across Broward County. Aluminum is the default answer within a few blocks of the water, and it is a good one, but it is not the immune material some brochures imply. It corrodes differently and more slowly, and it fails in places steel does not.
The first is galvanic pairing. Put a stainless bolt through an aluminum rail in salt air and the aluminum is the metal that gives up material, quietly, around the hole. Nylon shoulder washers and isolation bushings solve it for a few dollars per connection. Their absence is invisible on installation day and obvious four years later when a hinge plate has loosened on the leaf. Saturated air is all the electrolyte that reaction needs.
The second is welding. Heat takes the temper out of an extrusion around every weld, so a heavily welded aluminum leaf is softest exactly where it is carrying load. On wide gates we prefer mechanically fastened corners with internal gussets, which keeps the extrusion at full strength and lets the frame move a little in the heat instead of cracking a bead. The annealed band next to a bead keeps perhaps half the yield strength the mill delivered.
The third is filiform corrosion under the coating, which is the aluminum equivalent of undercutting and gets in through cut edges. Every field cut end needs sealing. Gates that are trimmed on site to fit a post spacing nobody measured properly are the ones that show a line of bubbling along one stile. It travels as a thread beneath the film and shows as a raised line rather than a blister.
Where aluminum genuinely earns its keep is weight. A lighter leaf puts less load on hinges and on operator gearing, both of which are already fighting salt, so the whole assembly lasts longer for reasons that have nothing to do with the alloy itself. On a twenty foot slide that is a couple of hundred pounds the gearbox no longer has to start twenty times a day.
Connections are worth specifying by name. A machine screw threaded straight into a thin extrusion wall strips under load, so we tap into a thicker internal boss or use a backing plate and a through bolt. Every stainless fastener gets a nylon shoulder washer and a bushing in the hole, torqued to a figure rather than to feel, because an overtightened bolt crushes the isolation it was meant to sit inside.
If your lot is inland, the calculation shifts. Steel is stiffer, cheaper for the same span, and perfectly reasonable west of the Turnpike. We build a lot of aluminum here because of where the houses are, not because aluminum is always the better product.
With 15+ years of experience, our insured team brings the right materials and equipment to every job — wrought iron and ornamental steel fabrication, marine-grade powder-coated aluminum, cantilever and roller slide gates, LiftMaster, DoorKing and FAAC operators, Class I-IV operator classifications, UL 325 entrapment protection — and backs the work with a written workmanship warranty. We serve Fort Lauderdale and nearby communities including Pompano Beach, Oakland Park, Wilton Manors, Lauderdale-by-the-Sea.
What We Handle
Everything our aluminum gates in Fort Lauderdale covers
One crew, one point of contact, and the full range of aluminum gates work in Fort Lauderdale, FL. If it is on this list we do it in house rather than handing it to a subcontractor:
- aluminum driveway gates
- marine-grade aluminum gates
- rust-free gates Fort Lauderdale
- powder-coated aluminum gates
- aluminum swing gates
- aluminum slide gates
- aluminum privacy gates
- waterfront property gates
- aluminum pool and pedestrian gates
- aluminum gate repair
- aluminum fence and gate packages
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Fort Lauderdale services.
Materials, equipment and how we do aluminum gates
The difference between aluminum gates that lasts and aluminum gates that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with wrought iron and ornamental steel fabrication, marine-grade powder-coated aluminum, cantilever and roller slide gates, LiftMaster, DoorKing and FAAC operators, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Fort Lauderdale job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. 15+ years of gate work in Broward County means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do aluminum gates outside Fort Lauderdale
Fort Lauderdale Gate Pros covers Fort Lauderdale and the surrounding communities of Broward County. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Aluminum Gates in Pompano Beach, FL — Broward County, incorporated as the Town of Pompano on July 3, 1908, population 112,046 at the 2020 census
- Aluminum Gates in Oakland Park, FL — Broward County, incorporated as Floranada on November 25, 1925, population 44,229 at the 2020 census
- Aluminum Gates in Wilton Manors, FL — Broward County, incorporated as a village on May 13, 1947, population 11,426 at the 2020 census
- Aluminum Gates in Lauderdale-by-the-Sea, FL — Broward County, incorporated November 30, 1927, population 6,198 at the 2020 census
- Aluminum Gates in Lighthouse Point, FL — Broward County, incorporated as a town on June 13, 1956, population 10,486 at the 2020 census
- Aluminum Gates in Deerfield Beach, FL — Broward County, incorporated as a town on May 12, 1939, population 86,859 at the 2020 census
Start on the Fort Lauderdale Gate Pros homepage for a free estimate, or call (844) 938-4596 and describe the job.
Why Fort Lauderdale Chooses Fort Lauderdale Gate Pros
- ✓Over 15 years installing and automating gates across Broward County
- ✓In-house metal shop — we weld and powder coat our own gates rather than drop-shipping them
- ✓Marine-grade aluminum and hot-dip galvanized steel specified for coastal salt air
- ✓Waterfront, canal-front and marina-community gate work is a specialty, not a sideline
The standards behind aluminum gates
Quality here is not a matter of opinion — it is written down. The aluminum gates work we do in Fort Lauderdale follows published industry standards: DASMA is the standards body for door and access systems, and UL Solutions publishes UL 325, the safety standard for automatic gate operators. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every aluminum gates project in Fort Lauderdale gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 938-4596 for a free aluminum gates free estimate in Fort Lauderdale, or request a quote and we'll get right back to you.